Lenze E94AYCEO Communications Manual Download Page 114

Page: 114 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

114

Parameter reference

13.3

Parameters of the communication module for slot MXI2

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C14874

C14875

C14880

Parameter | Name:

C14874 | CIP Connections Timeout Time

Data type: UNSIGNED_32

Index: 9701 = 0x25E5

Display of the timeouts (ms) of the CIP connections

Display range

(min. value | unit | max. value)

4294967295

Subcodes

Info

C14874/1

Timeout time of CIP connection 1

...

C14874/8

Timeout time of CIP connection 8



Read access



Write access



CINH



PLC STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C14875 | CIP Connections RUN/IDLE Flag

Data type: UNSIGNED_16

Index: 9700 = 0x25E4

Display of the run and idle flags of the CIP connections

Selection list

(read only)

0 Nonexistent
1 IDLE
2 RUN

Subcodes

Info

C14875/1

RUN/IDLE flag - CIP connection 1

...

C14875/8

RUN/IDLE flag - CIP connection 8



Read access



Write access



CINH



PLC STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C14880 | Reaction on communication fault

Data type: UNSIGNED_8

Index: 9695 = 0x25DF

Setting of the monitoring response in the event of a

Fault with regard to EtherNet/IP communication (



74)

(Mapping of the Lenze object

Lenze Class (101 / 0x65) (



139)

)

A change in the monitoring response becomes immediately effective.

Selection list

0 No response
1 Fault
3 Quick stop by trouble
4 Warning Locked
6 Information

Subcodes

Lenze setting

Info

C13880/1

0: No Response

Idle Mode

C13880/2

0: No Response

Fault Mode

(only for "exclusive owner" connections)

C13880/3

0: No Response

Expl. message timeout

C13880/4

0: No Response

Overall Ethernet communication timeout



Read access



Write access



CINH



PLC STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 114 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: