Lenze AC Tech ESVZAP0 Communications Interface Reference Manual Download Page 28

Page: 28 / 49

CMVPFB01A

Cyclic Data Access - Din Mapping

5.4.12 P46x = 3, Lenze C150 Status Word

The Lenze C150 Status Word consists of 16 control bits some of which are reserved.

Table 18: Lenze C150 Status Word

b15

b14

b13

b12

b11

b10

Drive

Healthy

Direction

of Rotation

Over

Voltage

Over Temp

Warning

Controller Status

Controller

Inhibit

Zero Speed

Above
Speed

At Setpoint

Speed

Reserved

Current Limit

Status

Pulse

Inhibit

Reserved

Table 19: Lenze C150 Status Word BIT Functions

BIT

Function

Description

Reserved

Pulse Inhibit

0 = Pulse outputs enabled
1 = Pulse outputs inhibited

Current Limit Status

0 = Current limit not reached
1 = Current limit reached

Reserved

At Setpoint Speed

0 = Actual output frequency <> Setpoint value
1 = Actual output frequency = Setpoint value

Above Speed

0 = Actual output frequency <= P136 value
1 = Actual output frequency > P136 value

At Zero Speed

0 = Actual output frequency <> 0 Hz
1 = Actual output frequency = 0 Hz

Controller Inhibit

0 = Controller Enabled
1 = Controller Inhibited

Controller

Status

0 = No Fault
8 = Fault Present

Over Temp Warning

0 = No over-temperature fault
1 = Over-temperature fault

Over Voltage

0 = No DC bus over-voltage
1 = DC bus over-voltage

Direction of Rotation

0 = CW (FORWARD)
1 = CCW (REVERSE)

Drive Ready

0 = Not ready
1 = Ready (No Faults)

5.4.13 P46x = 4, Actual Speed in RPMs

Unsigned Actual Speed in RPMs. Range: 0 - 65535.

Summary of Contents for ESVZAP0


















































Search results

Summary of Contents for ESVZAP0

Reviews:

Related manuals for ESVZAP0

Brands by name

Popular brands

Lenze AC Tech ESVZAP0, Communications Interface Reference Manual

Search results

Summary of Contents for ESVZAP0

Reviews:

Related manuals for ESVZAP0

Brands by name

Popular brands