manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

• Before you make changes to disk drives, disk drive controllers (including controllers that are integrated

on the system board), disk drive backplanes, or disk drive cables, back up all important data that is
stored on hard disks.

• Before you remove any component of a RAID array, back up all RAID configuration information.

To remove a hot-swap hard disk drive, complete the following steps.

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Make sure you save the data on your drive, especially if it is part of a RAID array, before you
remove it from the server.

Step 3.

Slide the release latch (orange) gently to the left to unlock the drive handle.

0000

0000

0000

0000

0000

000

000

000

000

000

Latch

Handle

Figure 162. 2.5-inch hot-swap hard disk drives removal

00

00

00

00

00

0

0

0

0

0

000

000

000

000

000

000

000

000

000

0000

0000

0000

0000

Latch

Handle

Filler panel

3.5-inch hot-swap
hard disk drive

Figure 163. 3.5-inch hot-swap hard disk drives removal

Step 4.

Grasp the handle and slide the drive out of the drive bay.

Step 5.

Reinstall the drive bay filler panel.

Step 6.

If you are instructed to return the drive assembly, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Replacing a hot-swap hard disk drive

Use this information to install a hot-swap hard disk drive.

250

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM 8832 Deployment Manual preview
8832
Brand: IBM Pages: 54
Watchguard Firebox M470 Hardware Manual preview
Firebox M470
Brand: Watchguard Pages: 32
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
MSI K9ND Speedster User Manual preview
K9ND Speedster
Brand: MSI Pages: 106
Blackberry ENTERPRISE SERVER FOR NOVELL GROUPWISE Installation And Configuration Manual preview
ENTERPRISE SERVER FOR NOVELL GROUPWISE
Brand: Blackberry Pages: 73
Belkin F1UP0002 Quick Installation Manual preview
F1UP0002
Brand: Belkin Pages: 2
QNAP TVS- 72XU Series User Manual preview
TVS- 72XU Series
Brand: QNAP Pages: 56
Supero SUPERSERVER 7045W-NTR+ User Manual preview
SUPERSERVER 7045W-NTR+
Brand: Supero Pages: 146
D-Link 301P - DP Print Server Manual preview
301P - DP Print Server
Brand: D-Link Pages: 150
Planet FPS-1101 User Manual preview
FPS-1101
Brand: Planet Pages: 83
Enconnex Advanced Office-in-a-Box User Manual preview
Advanced Office-in-a-Box
Brand: Enconnex Pages: 40
XtendLan TC-40xL User Manual preview
TC-40xL
Brand: XtendLan Pages: 50
Planet FPS-1012N User Manual preview
FPS-1012N
Brand: Planet Pages: 141
Viavi G4-10G-010-96T Manual preview
G4-10G-010-96T
Brand: Viavi Pages: 12
Inspur NF5170M4 User Manual preview
NF5170M4
Brand: Inspur Pages: 112
Inspur AGX-5 User Manual preview
AGX-5
Brand: Inspur Pages: 170
Gateway 920 User Manual preview
920
Brand: Gateway Pages: 151
Celestix E6600 Installation Manual preview
E6600
Brand: Celestix Pages: 68

Brands by name

Popular brands

Load more brands