manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual, Page: 253 / 1222

Share
Download
Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 253

Step 2.

Position the cover on top of the server.

Step 3.

Slide the cover toward the front of the server.

Step 4.

Make sure that the cover correctly engages all the inset tabs on the server.

Step 5.

Press down the blue latch on the top of the cover.

0

0

0

0

0

0

0

0

000

000

000

000

000

000

000

000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00000000000000000

00

00

00

00000

00000

00000

000

000

00000

00000

00000

Cover-release
latch

1

2

Figure 153. Cover installation

Step 6.

Slide the server all the way into the rack until it latches.

Step 7.

Reconnect the external cables and power cords.

Removing the air baffle

When you work with some optional devices, you must first remove the air baffle to access certain
components or connectors on the system board. The following illustration shows how to remove the air
baffle.

Chapter 6

.

Removing and replacing components

241

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments