manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

SAS/SATA
backplane
power cable

The following illustration shows the cabling information for the hardware RAID cable in the server:

SAS signal cables

Port 0-3

Port 4-5

Port 0-3

Port 4-5

Removing and replacing server components

This section provides information for removing and replacing components in the server.

Removing and replacing structural parts

Replacement of structural parts is your responsibility. If Lenovo installs a structural part at your request,
you will be charged for the installation.

Chapter 6

.

Removing and replacing components

239

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Unisys ES5000 Manual preview
ES5000
Brand: Unisys Pages: 20
Xerox M Series Initial Setup Card preview
M Series
Brand: Xerox Pages: 2
Cabletron Systems MicroMMAC 22ES Installation Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 93
Gateway 7250R Rack Mounting Instructions preview
7250R
Brand: Gateway Pages: 26
Lantronix SLC 8000 Demo Manual preview
SLC 8000
Brand: Lantronix Pages: 10
Lantronix xport pro Integration Manual preview
xport pro
Brand: Lantronix Pages: 17
Lantronix PremierWave XC User Manual preview
PremierWave XC
Brand: Lantronix Pages: 109
Lantronix XPort Integration Manual preview
XPort
Brand: Lantronix Pages: 24
Lantronix WiPort Integration Manual preview
WiPort
Brand: Lantronix Pages: 29
Lantronix XPress DR+ Quick Connect preview
XPress DR+
Brand: Lantronix Pages: 2
IBM 9123710 - eServer OpenPower 710 Introduction Manual preview
9123710 - eServer OpenPower 710
Brand: IBM Pages: 70
Rackable Systems S3116-NAS Getting Started Manual preview
S3116-NAS
Brand: Rackable Systems Pages: 4
TRENDnet TS-U100 - NAS Server - USB User Manual preview
TS-U100 - NAS Server - USB
Brand: TRENDnet Pages: 47
LaCie 301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard... User Manual preview
301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...
Brand: LaCie Pages: 74
Edimax Past Ethernet Combo Print Server PS-1216U Quick Installation Manual preview
Past Ethernet Combo Print Server PS-1216U
Brand: Edimax Pages: 23
USR IOT USR-N580 User Manual preview
USR-N580
Brand: USR IOT Pages: 56
USRIOT USR-N520 User Manual preview
USR-N520
Brand: USRIOT Pages: 69
NuPrime Omnia S1 User Manual preview
Omnia S1
Brand: NuPrime Pages: 26

Brands by name

Popular brands

Load more brands