manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Enabling Features on Demand Ethernet software

You can activate the Features on Demand (FoD) software upgrade key for Fibre Channel over Ethernet (FCoE)
and iSCSI storage protocols that is integrated in the integrated management module.

For more information and instructions for activating the Features on Demand Ethernet software key, see
the

Features on Demand User’s Guide

. To download the document, go to https://fod.lenovo.com/lkms,

log in, and click

Help

.

Enabling Features on Demand RAID software

You can activate the Features on Demand (FoD) software upgrade key for RAID that is integrated in the
integrated management module.F

For more information and instructions for activating the Features on Demand RAID software key, see the

Features on Demand User’s Guide

. To download the document, go to https://fod.lenovo.com/lkms, log

in, and click

Help

.

Configuring RAID arrays

Through the Setup utility, you can access utilities to configure RAID arrays.

The specific procedure for configuring arrays depends on the RAID controller that you are using. For details,
see the documentation for your RAID controller. To access the utility for your RAID controller, complete the
following steps:

Step 1.

Turn on the server.

Note:

Approximately 10 seconds after the server is connected to power, the power-control button

becomes active.

Step 2.

When prompted,

<F1 Setup>

is displayed, press F1. If you have set an administrator password, you

must type the administrator password to access the full Setup utility menu. If you do not type the
administrator password, a limited Setup utility menu is available.

Step 3.

Select

System Settings

➙

Storage

.

Step 4.

Press Enter to refresh the list of device drivers.

Step 5.

Select the device driver for your RAID controller and press Enter.

Step 6.

Follow the instructions in the documentation for your RAID controller.

Using Lenovo XClarity Administrator

The initial setup of Lenovo XClarity Administrator includes the following:

• Preparing the network

• Installing and configuring the Lenovo XClarity Administrator virtual appliance

• Managing systems

• Setting up automatic problem notification optionally

To manage systems based on the network topology that is implemented in your environment, there are a
number of different ways to connect manageable systems to the network and to set up the Lenovo XClarity
Administrator. If you plan to use Lenovo XClarity Administrator to manage the server, you must check for the
latest applicable Lenovo XClarity Administrator updates. For installing the Lenovo XClarity Administrator in
VMware ESXi-based and Hyper-V environments and downloading Lenovo XClarity Administrator updates, go
to:
https://support.lenovo.com/us/en/ documents/LNVO-XCLARIT

156

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM 5100 Installation Manual preview
5100
Brand: IBM Pages: 64
GlobalTime Electronic GTT-400 Manual preview
GTT-400
Brand: GlobalTime Electronic Pages: 19
IBM Eserver 345 Series Option Installation Manual preview
Eserver 345 Series
Brand: IBM Pages: 70
Pathos Acoustics Musiteca Operating Instructions Manual preview
Musiteca
Brand: Pathos Acoustics Pages: 26
Supermicro SUPERSERVER 1015B-3 User Manual preview
SUPERSERVER 1015B-3
Brand: Supermicro Pages: 98
IBM eServer BladeCenter HS20Type 8832 Problem Determination And Service Manual preview
eServer BladeCenter HS20Type 8832
Brand: IBM Pages: 112
MSI WindBOX Series User Manual preview
WindBOX Series
Brand: MSI Pages: 18
IBM eServer xSeries 335 Type 8676 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 335 Type 8676
Brand: IBM Pages: 178
Fujitsu B23Q8WD-G-01-J Hardware Manual preview
B23Q8WD-G-01-J
Brand: Fujitsu Pages: 26
Fujitsu FUTRO S450 Operating Manual preview
FUTRO S450
Brand: Fujitsu Pages: 56
Fujitsu FD-1000ST User Manual preview
FD-1000ST
Brand: Fujitsu Pages: 36
Fujitsu FUTRO S550 Operating Manual preview
FUTRO S550
Brand: Fujitsu Pages: 61
Fujitsu BS2000 Operating Manual preview
BS2000
Brand: Fujitsu Pages: 30
Fujitsu ETERNUS DX Disk Configuration Manual preview
ETERNUS DX Disk
Brand: Fujitsu Pages: 85
Fujitsu BS2000/OSD Operation Manual preview
BS2000/OSD
Brand: Fujitsu Pages: 111
Fujitsu BX630 - PRIMERGY - S2 Dual Options Manual preview
BX630 - PRIMERGY - S2 Dual
Brand: Fujitsu Pages: 64
Fujitsu ESPRIMO A525-L Operating Manual preview
ESPRIMO A525-L
Brand: Fujitsu Pages: 68
Fujitsu CELVIN NAS QE707 Operating Manual preview
CELVIN NAS QE707
Brand: Fujitsu Pages: 95

Brands by name

Popular brands

Load more brands