manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

User Response

Complete the following steps:

1. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

2. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

3. Run the test again.

4. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

5. Run the test again.

6. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA system management test results

The following messages can result when you run the system management test.

Test results for the DSA system management test

The following messages can result when you run the DSA system management test.

•

166-000-001 : IMM I2C Test Passed

IMM I2C Test Passed.

Recoverable

No

Severity

Event

Serviceable

No

Automatically notify support

No

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-801-001 : IMM I2C Test Aborted

Appendix C. DSA diagnostic test results

1167

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

D-Link DP-300+ User Manual preview
DP-300+
Brand: D-Link Pages: 38
D-Link Epress EtherNetwork DP-301P+ Datasheet preview
Epress EtherNetwork DP-301P+
Brand: D-Link Pages: 2
NEC NECCare Gold Express5800/320Fd Service Manual preview
NECCare Gold Express5800/320Fd
Brand: NEC Pages: 10
NEC SV8500 Setup Manual preview
SV8500
Brand: NEC Pages: 84
NEC NEC Express5800 Series Release Note preview
NEC Express5800 Series
Brand: NEC Pages: 6
Atop MB5202 Series Hardware Installation Manual preview
MB5202 Series
Brand: Atop Pages: 2
IBM 87302RU Planning And Installation Manual preview
87302RU
Brand: IBM Pages: 140
CAAS Audio Digital Audio Server User Manual & Warranty preview
Digital Audio Server
Brand: CAAS Audio Pages: 23
IBM Bull Escala E5-700 Manual preview
Bull Escala E5-700
Brand: IBM Pages: 116
IBM ProtecTIER DD6 Instructions Manual preview
ProtecTIER DD6
Brand: IBM Pages: 10
Flexport HF2211 User Manual preview
HF2211
Brand: Flexport Pages: 39
Rackable Systems OmniStor 4900F Series User Manual preview
OmniStor 4900F Series
Brand: Rackable Systems Pages: 196
Icy Box IB-NAS6220 Specifications preview
IB-NAS6220
Brand: Icy Box Pages: 3
IBM eServer xSeries 205 Type 8480 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 205 Type 8480
Brand: IBM Pages: 168
Infotrend EonServ 7000 Series Quick Installation Manual preview
EonServ 7000 Series
Brand: Infotrend Pages: 2
Hitachi VisionBase 8880R Product Manual preview
VisionBase 8880R
Brand: Hitachi Pages: 62
Hitachi USP V Configuration Manual preview
USP V
Brand: Hitachi Pages: 70
Hitachi VisionBase 8450H Product Manual preview
VisionBase 8450H
Brand: Hitachi Pages: 126

Brands by name

Popular brands

Load more brands