manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

6. Run the test again.

7. Execute the standard DSA memory diagnostics to validate all memory.

8. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-902-000 : MemStr Test Failed

Memory size is insufficient to run the test.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Ensure that all memory is enabled by checking the "Available System Memory" in the "Resource

Utilization" section of the DSA Diagnostic Event log.

2. If necessary, access the Configuration/Setup Utility program by pressing F1 during system

boot and enable all memory.

3. Make sure that the DSA Diagnostic code is at the latest level.

4. Run the test again.

5. Execute the standard DSA memory diagnostics to validate all memory.

6. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Nvidia GPU test results

The following messages can result when you run the Nvidia GPU test.

Appendix C. DSA diagnostic test results

1155

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

NEC Express5800/180Ra-7 Datasheet preview
Express5800/180Ra-7
Brand: NEC Pages: 2
NEC Express5800/120Rh-2 Getting Started Manual preview
Express5800/120Rh-2
Brand: NEC Pages: 2
NEC Express5800/120Rh-2 Datasheet preview
Express5800/120Rh-2
Brand: NEC Pages: 2
NEC Express5800/120Rg-1 Datasheet preview
Express5800/120Rg-1
Brand: NEC Pages: 2
NEC Express5800/120Rf-1 Operation Manual preview
Express5800/120Rf-1
Brand: NEC Pages: 21
NEC Express5800/120Ra-1 Release Note preview
Express5800/120Ra-1
Brand: NEC Pages: 6
NEC Express5800/120Mc2 series Datasheet preview
Express5800/120Mc2 series
Brand: NEC Pages: 2
NEC EXPRESS5800/120Le Configuration Manual preview
EXPRESS5800/120Le
Brand: NEC Pages: 56
NEC Express5800 320La Installation Notes preview
Express5800 320La
Brand: NEC Pages: 8
NEC Express5800 120Li Datasheet preview
Express5800 120Li
Brand: NEC Pages: 2
NEC Express5800 120Ed Installation Procedures Manual preview
Express5800 120Ed
Brand: NEC Pages: 29
NEC Active Upgrade Express5800/320Fc Datasheet preview
Active Upgrade Express5800/320Fc
Brand: NEC Pages: 4
NEC 320Fc Read Me First preview
320Fc
Brand: NEC Pages: 10
NEC Express5800/120Rj-2 Configuration Manual preview
Express5800/120Rj-2
Brand: NEC Pages: 18
NEC Express5800/120Rh-1 Configuration Manual preview
Express5800/120Rh-1
Brand: NEC Pages: 20
NEC Bull NovaScale R620 Series User Manual preview
Bull NovaScale R620 Series
Brand: NEC Pages: 346
NEC Express5800 320La User Manual preview
Express5800 320La
Brand: NEC Pages: 206
NEC Express5800/R110j-1 Manual preview
Express5800/R110j-1
Brand: NEC Pages: 30

Brands by name

Popular brands

Load more brands