manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-901-000 : MLNX:MLNX_DiagnosticTestIBPort Test Failed

Port Test Failed.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Make sure that the physical link of the port under test in the active state and a subnet manager

running on the fabric to which the port is attached.

2. If these condition was met but the test keeps failing the port's adapter might be faulty.

3. Try replacing the adapter and repeating the test.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA memory isolation test results

The following messages can result when you run the memory isolation test.

Test results for the DSA memory isolation test

The following messages can result when you run the DSA memory isolation test.

•

201-000-000 : Standalone Memory Test Passed

Quick/Full Memory Test All CPUs Passed.

Recoverable

No

Severity

Event

Serviceable

No

1074

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

D-Link DSN-4100 Series Quick Start Manual preview
DSN-4100 Series
Brand: D-Link Pages: 2
KYLAND SICOM3005A Hardware Installation Manual preview
SICOM3005A
Brand: KYLAND Pages: 30
H3C UniServer R2900 G3 Installation, Quick Start preview
UniServer R2900 G3
Brand: H3C Pages: 15
Supermicro SSG-2029P-ACR24H User Manual preview
SSG-2029P-ACR24H
Brand: Supermicro Pages: 136
MSI MS-S0081 Manual preview
MS-S0081
Brand: MSI Pages: 54
Sony XDAAI1PK Brochure preview
XDAAI1PK
Brand: Sony Pages: 8
Sony BSV-M1 - StorStation NAS Server Operating Instructions Manual preview
BSV-M1 - StorStation NAS Server
Brand: Sony Pages: 58
National Instruments ENET-Serial Getting Started preview
ENET-Serial
Brand: National Instruments Pages: 4
Simpact Freeway 2000 Hardware Installation Manual preview
Freeway 2000
Brand: Simpact Pages: 86
Alfresco JLAN Installation Manual preview
JLAN
Brand: Alfresco Pages: 49
Red Hat 8.1 Installation Manual preview
8.1
Brand: Red Hat Pages: 120
Polycom KIRK 500 User Manual preview
KIRK 500
Brand: Polycom Pages: 34
Black Box LES421A User Manual preview
LES421A
Brand: Black Box Pages: 60
Star Lake SCH200 User Manual preview
SCH200
Brand: Star Lake Pages: 76
7th Sense VIOSO User Manual preview
VIOSO
Brand: 7th Sense Pages: 24
3onedata CP202-2CI Quick Installation Manual preview
CP202-2CI
Brand: 3onedata Pages: 3
Supero SC835BTQ - R1K28B User Manual preview
SC835BTQ - R1K28B
Brand: Supero Pages: 86
Supero FatTwin F517H6-FT User Manual preview
FatTwin F517H6-FT
Brand: Supero Pages: 130

Brands by name

Popular brands

Load more brands