Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 1084

Page: 1084 / 1222

Test results for the DSA Mellanox adapter test

The following messages can result when you run the DSA Mellanox adapter test.

•

408-000-000 : MLNX:MLNX_DiagnosticTestEthernetPort Test Passed

Port Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-001-000 : MLNX:MLNX_DiagnosticTestIBPort Test Passed

Port Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-800-000 : MLNX:MLNX_DiagnosticTestEthernetPort Test Aborted

Port Test was canceled.

Recoverable

Severity

Warning

Serviceable

1072

Lenovo System x3650 M4 Installation and Service Guide

«
...
1082
1083
1084
1085
1086
...
»

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands