manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

516-902-000 : ELXUCNA: ELXUCNA: NIC LED(Beacon)Test Failed

A failure was detected while verifying operation of the status LEDs.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA EXA port ping test results

The following messages can result when you run the EXA port ping test.

Test results for the DSA EXA port ping test

The following messages can result when you run the DSA EXA port ping test.

Appendix C. DSA diagnostic test results

1059

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM 150 User Reference Manual preview
150
Brand: IBM Pages: 180
Patton electronics 3120 Administrator'S Reference Manual preview
3120
Brand: Patton electronics Pages: 331
Aastra AXD Installation And Maintenance Manual preview
AXD
Brand: Aastra Pages: 502
H3C UniServer R4900 G5 Operating System Installation Manual preview
UniServer R4900 G5
Brand: H3C Pages: 141
ImageTech printWiFi User Manual preview
printWiFi
Brand: ImageTech Pages: 44
TYAN Transport GT26-B4987 Service Manual preview
Transport GT26-B4987
Brand: TYAN Pages: 125
IBM BladeCenter HS20 Type 8843 Installation And User Manual preview
BladeCenter HS20 Type 8843
Brand: IBM Pages: 112
Quatech 4-Port USB 2.0 Device Server over IP... Specifications preview
4-Port USB 2.0 Device Server over IP...
Brand: Quatech Pages: 2
Sun Microsystems Sun Fire X4250 Volume Configuration Manual preview
Sun Fire X4250
Brand: Sun Microsystems Pages: 12
Olive Olive OPUS N5 User Manual preview
Olive OPUS N5
Brand: Olive Pages: 24
Inspur NF5486M5 Installation Manual preview
NF5486M5
Brand: Inspur Pages: 2
Johnson Controls Rackmount 5000 Series Quick Installation Manual preview
Rackmount 5000 Series
Brand: Johnson Controls Pages: 42
Canon imagePRESS Server G200 Configuration And Setup preview
imagePRESS Server G200
Brand: Canon Pages: 98
Canon imagePRESS A3200 Installation And Service Manual preview
imagePRESS A3200
Brand: Canon Pages: 192
Canon ColorPass-Z7400 Configuration Manual preview
ColorPass-Z7400
Brand: Canon Pages: 210
Cisco Aironet 1500 Series Datasheet preview
Aironet 1500 Series
Brand: Cisco Pages: 8
Cisco 7835-H2 - Media Convergence Server Datasheet preview
7835-H2 - Media Convergence Server
Brand: Cisco Pages: 8
Cisco APP1000 - One Application Server Appliance Installation And Administration Manual preview
APP1000 - One Application Server Appliance
Brand: Cisco Pages: 20

Brands by name

Popular brands

Load more brands