Lenovo x3250 m6 Installation And Service Manual Download Page 27 | Manualshive

Page: 27 / 696

background image

• On-Board Pre-Boot Diagnostics
• Ethernet Diagnostics
• RAID Diagnostics
• Installation and Service Guide

Turning on or turning off the server

When the server is connected to an ac power source but is not turned on, the operating system does not
run, and all core logic except for the Integrated Management Module II (IMM2) is shut down.

However, the server can respond to requests from Integrated Management Module II (IMM2), such as a
remote request to turn on the server. The power-on LED flashes to indicate that the server is connected to
ac power but is not turned on.

Turning on the server

Approximately 20 seconds after the server is connected to ac power, one or more fans might start running to
provide cooling and the power-on button LED starts blinking quickly. Approximately one to three minutes
after the server is connected to ac power, the power-control button becomes active and the blink of the
power-on button LED turns slow.

You can turn on the server by pressing the power-control button.

You also can turn on the server through the Wake on LAN feature if supported by the operating system. You
can send a request through the Wake on LAN feature to turn on the server remotely.

Besides, if a power failure occurs while the server is turned on, the server will restart automatically when
power is restored.

Turning off the server

Use this information to turn off the server.

When you turn off the server and leave it connected to ac power, the server can respond to requests from
theIntegrated Management Module II (IMM2), such as a remote request to turn on the server. While the
server remains connected to ac power, one or more fans might continue to run. To remove all power from
the server, you must disconnect the server from the power source.

Some operating systems require an orderly shutdown before you turn off the server. For information about
shutting down the operating system, see your operating-system documentation or help system.

CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.

.

About the Lenovo System x3250 M6 server

13

«
...
25
26
27
28
29
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

ioLogik W5300 Series

Brand: Moxa Technologies Pages: 177

Brand: KYLAND Pages: 30

Brand: AIC Pages: 112

SUPERSERVER 6027TR-H71FRF

Brand: Supero Pages: 118

Netfinity Series

Brand: IBM Pages: 44

AlphaServer ES45 1B

Brand: Compaq Pages: 322

Ultrastar Serv60+8

Brand: Western Digital Pages: 406

Brand: Stratus Pages: 106

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

Brand: EXAGATE Pages: 8

Palcare PAL-211401

Brand: PalatiumCare Pages: 64

Brand: Hitachi Pages: 57

Brand: Hitachi Pages: 76

BladeSymphony 1000

Brand: Hitachi Pages: 52

Brand: Hitachi Pages: 91

Brand: Hitachi Pages: 174

HVM Navigator V03-06

Brand: Hitachi Pages: 312

NVM Navigator v03-07

Brand: Hitachi Pages: 316

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands