Lenovo x3250 m6 Installation And Service Manual Download Page 151

Page: 151 / 696

Step 5.

Lift the blue tabs on the backplane to disengage and remove the backplane from the chassis.

Figure 73. 2.5-inch hot-swap hard-disk-drive backplane removal

Installing the 2.5-inch hot-swap hard-disk-drive backplane

The following illustration shows contents of the second 2.5-inch hard-disk-drive backplane upgrade kit:

Figure 74. The second 2.5-inch hard-disk-drive backplane upgrade kit

Mini-SAS signal cable connector

Power connector

To install the 2.5-inch hot-swap hard-disk-drive backplane, do the following:

Chapter 7

Removing and installing server components

137

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands