Lenovo x3250 m6 Installation And Service Manual Download Page 143 | Manualshive

Page: 143 / 696

background image

Removing the fixed power supply

When you remove the fixed power supply, observe the following precautions.

CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with
one of these parts, contact a service technician.

Note:

After you remove the fixed power supply, you need to install a new one. See “Installing the fixed

power supply” on page 130.

To remove the fixed power supply, do the following:

Step 1.

Turn off the server. Then, disconnect all external cables and remove all peripheral devices.

Step 2.

Remove the server cover. See “Removing the server cover” on page 88.

Step 3.

Disconnect the power-supply cables from the connectors on the system board and internal
devices. Then, disengage the cables from any retention clips.

Note:

Record the routing of all power-supply cables; you will route the power-supply cables the

same way when you install the power supply.

Step 4.

Remove the fixed power supply.

a.

Remove the screws that secure the power supply to the rear of the chassis.

b.

Push the power supply toward the front of the server until the power supply has disengaged
from the chassis.

c.

Lift the power supply out of the chassis.

Removing and installing server components

129

«
...
141
142
143
144
145
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Express5800/T110g-E

Brand: NEC Pages: 2

Brand: IBM Pages: 198

Brand: 7starlake Pages: 32

847620U - Netfinity 3000 - 20U

Brand: IBM Pages: 270

Brand: Axel Pages: 28

System X Series

Brand: IBM Pages: 6

xSeries 342 2RX

Brand: IBM Pages: 158

Brand: QNAP Pages: 39

Brand: Imagine Pages: 2

Brand: ImageQuest Pages: 31

Brand: DSP Pages: 140

Brand: Black Box Pages: 3

5325302053 - Snap Server 720i NAS

Brand: Adaptec Pages: 238

Brand: SSS Siedle Pages: 12

Brand: 3Com Pages: 65

Brand: d3 Technologies Pages: 10

Brand: Oracle Pages: 208

Brand: Gigabyte Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands