manualshive.com logo in svg

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Share
Download
Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 120

6. Insert the TPM into the TPM connector on the system board.

Figure 55. Installing the TPM

7. If you have lifted the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card

assembly 1” on page 145.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation, go to “Completing the parts replacement” on page 155. Then, you can

configure the TPM function in the Setup Utility program. See “Configuring the TPM function” on page 52.

Removing the ThinkServer Trusted Platform Module

Attention:

Do not open your server or attempt any repair before reading and understanding “Safety information”

on page iii and “Guidelines” on page 69.

This topic provides instructions on how to remove the TPM if the server has one installed.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

106

ThinkServer RD330 Hardware Maintenance Manual

Summary of Contents for tihnkserver rd330







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands