Lenovo ThinkSystem SR650 V2 Reference Download Page 26

Page: 26 / 212

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPUN0019M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPUN0020N

Sensor [SensorElementName] has transitioned to non-recoverable
from a less severe state.

Error

FQXSPUN0023N

Sensor [SensorElementName] has transitioned to non-recoverable.

Error

FQXSPUN0050M

The RAID controller in PCI slot [arg1] is in critical state. At least one
logical drive is offline.

Error

FQXSPUN0053M

The RAID controller in PCI slot [arg1] is in critical status. At least one
physical drive is failed.

Error

FQXSPUN0054M

The RAID controller in PCI slot [arg1] is in critical status. At least one
logical drive is now degraded or partially degraded.

Error

FQXSPUN0055M

The RAID controller in PCI slot [arg1] is in critical state. Battery is in
non-optimal state.

Error

FQXSPUP0007L

Invalid or Unsupported firmware or software was detected on system
[ComputerSystemElementName].

Error

FQXSPUP4000I

Please ensure that the Management Controller [arg1] is flashed with
the correct firmware. The Management Controller is unable to match
its firmware to the server.

Error

FQXSPUP4003I

[arg1] firmware mismatch internal to system [arg2]. Please attempt to
flash the [arg3] firmware.

Error

FQXSPUP4004I

XCC firmware mismatch between nodes/servers [arg1] and [arg2].
Please attempt to flash the XCC firmware to the same level on all
nodes/servers.

Error

FQXSPUP4005I

FPGA firmware mismatch between nodes/servers [arg1] and [arg2].
Please attempt to flash the FPGA firmware to the same level on all
nodes/servers.

Error

List of XClarity Controller events

This section lists all messages that can be sent from the XClarity Controller.

•

FQXSPBR4000I: Management Controller [arg1]: Configuration restored from a file by user [arg2].

This message is for the use case where a user restores a Management Controller configuration from a file.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0027

User Action:

Information only; no action is required.

•

FQXSPBR4001I: Running the backup Management Controller [arg1] main application.

This message is for the use case where a Management Controller has resorted to running the backup
main application.

ThinkSystem SR650 V2 Messages and Codes Reference

Summary of Contents for ThinkSystem SR650 V2





















































































































































































































Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands

Lenovo ThinkSystem SR650 V2, Reference

Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands