Lenovo thinksystem SN850 7X15 Setup Manual Download Page 63

Page: 63 / 88

Figure 38. Disconnecting cable from RAID adapter

If you are instructed to return the component or optional device, follow all packaging instructions, and use
any packaging materials for shipping that are supplied to you.

Install the air baffle

Use this information to install the air baffle.

1. Read “Installation Guidelines” on page 26 to ensure that you work safely.

2. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with the

bezel pointing toward you.

3. Remove the compute node cover (see “Remove the compute node cover” on page 29 for instructions).

To install the air baffle, complete the following steps:

Watch the procedure

. A video of the installation process is available:

• Youtube: https://www.youtube.com/playlist?list=PLYV5R7hVcs-DtV8A4UWy7d3AoFKjCvas3
• Youku: http://list.youku.com/albumlist/show/id_50481024

Chapter 3

Compute node hardware setup

Summary of Contents for thinksystem SN850 7X15

























































































Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands

Lenovo thinksystem SN850 7X15, Setup Manual

Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands