manualshive.com logo in svg

Lenovo ThinkStation P360 Tower, Hardware Maintenance Manual, Page: 97 / 116

Share
Download
Lenovo ThinkStation P360 Tower Hardware Maintenance Manual Download Page 97

Power supply assembly

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

Although there are no moving parts in the computer after the power cord has been disconnected, the 
following warnings are required for your safety.

Keep fingers and other parts of your body away from hazardous, moving parts. If you suffer an injury, seek 
medical care immediately. Never remove the cover on a power supply or any part that has the following label 
attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. 
There are no serviceable parts inside these components. If you suspect a problem with one of these parts, 
contact a service technician.

For access, do the following:  

1.  Remove these parts in order, if any: 

•  “Computer cover” on page 53

•  “Optical drive” on page 54

•  “Front bezel” on page 55

•  “Primary hard disk drives” on page 56

•  “3.5-inch primary hard disk drive cage” on page 61

2.  Disconnect the power supply assembly cables from the system board.

Removal steps

Chapter 7

.

Hardware removal and installation

91

Summary of Contents for ThinkStation P360 Tower





















































































































Reviews:

No comments