manualshive.com logo in svg

Lenovo ThinkStation P360 Tower, Hardware Maintenance Manual, Page: 92 / 116

Share
Download
Lenovo ThinkStation P360 Tower Hardware Maintenance Manual Download Page 92

Replacement procedure of the 125-watt heat-sink-and-fan assembly

1.  Remove the four screws that secure the heat-sink-and-fan assembly to the chassis. Then, follow the 

following sequence to loosen the four screws that secure the heat-sink-and-fan assembly to the system 
board. Then, lift the heat-sink-and-fan assembly off the system board. 

•  Partially loosen screw 

2a

, fully loosen screw 

2b

, and then fully loosen screw 

2a

.

•  Partially loosen screw 

2c

, fully loosen screw 

2d

, and then fully loosen screw 

2c

.

Notes: 

•  Carefully loosen the four screws to avoid any possible damage to the system board. The four screws 

cannot be removed from the heat-sink-and-fan assembly.

•  You might have to gently twist the heat-sink-and-fan assembly to free it from the microprocessor.

•  Do not touch the thermal grease while handling the heat-sink-and-fan assembly.

•  In case you need to remove the chassis beam as well, ensure that the 125-watt heat-sink-and-fan 

assembly has been removed before you remove the chassis beam.

86

P360 Tower Hardware Maintenance Manual

Summary of Contents for ThinkStation P360 Tower





















































































































Reviews:

No comments