manualshive.com logo in svg

Lenovo ThinkStation P360 Tower, Hardware Maintenance Manual, Page: 101 / 116

Share
Download
Lenovo ThinkStation P360 Tower Hardware Maintenance Manual Download Page 101

Flexible I/O board

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

For access, remove these parts in order, if any: 

•  “Computer cover” on page 53

•  “E-lock” on page 92

•  “Rear fan” on page 83

•  Type-2 heat sink and fan assembly, if any. See “Heat-sink-and-fan assembly” on page 84

Removal steps

Internal speaker

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

For access, do the following:  

1.  Remove these parts in order, if any: 

•  “Computer cover” on page 53
•  “Optical drive” on page 54
•  “Front bezel” on page 55
•  “Optical drive cage” on page 74

2.  Disconnect the internal speaker cable from the system board.

Chapter 7

.

Hardware removal and installation

95

Summary of Contents for ThinkStation P360 Tower





















































































































Reviews:

No comments