manualshive.com logo in svg

Lenovo ThinkCentre M90t Gen 3, Hardware Maintenance Manual, Page: 64 / 104

Share
Download
Lenovo ThinkCentre M90t Gen 3 Hardware Maintenance Manual Download Page 64

Removal steps of the 3.5-inch secondary storage drive, plastic bracket, and cage

M.2 solid-state drive and heat sink

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

Before you open the computer cover, turn off the computer and wait several minutes until the computer is 
cool.

Attention:

The internal storage drive is sensitive. Inappropriate handling might cause damage and 

permanent loss of data. When handling the internal storage drive, observe the following guidelines: 

•  Replace the internal storage drive only for upgrade or repair. The internal storage drive is not designed for 

frequent changes or replacement.

•  Before replacing the internal storage drive, make a backup copy of all the data that you want to keep.

•  Do not touch the contact edge of the internal storage drive. Otherwise, the internal storage drive might get 

damaged.

•  Do not apply pressure to the internal storage drive.

58

M90t Gen 3 Hardware Maintenance Manual

Summary of Contents for ThinkCentre M90t Gen 3









































































































Reviews:

No comments