Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 49 | Manualshive

Page: 49 / 296

background image

• Some cable connectors have locks or latches that must be disengaged to disconnect the cable.

For information about RAID card cable routing, see “Cable routing for drives” on page 45.

Figure 25. RAID card connectors (type 1)

Table 20. RAID card connectors (type 1)

Callout

Callout

1

RAID flash power module (J14) connector

4

RAID connector for drive backplane 2 or 5 (SAS only)

2

Unused

5

RAID connector for drive backplane 1 or 4 (SAS only)

3

RAID connector for drive backplane 3 or 6 (SAS only)

6

PCI connector to storage interposer

Figure 26. RAID card connectors (type 2)

Table 21. RAID card connectors (type 2)

Callout

Callout

1

RAID flash power module (J14) connector

3

RAID connector for drive backplane 1 or 4 (SAS only)

2

RAID connector for drive backplane 2 or 5 (SAS only)

4

PCI connector to storage interposer

Drive backplane connectors

The following illustration shows the internal connectors on the drive backplanes.

Note:

Some cable connectors have locks or latches that must be disengaged to disconnect the cable.

There are two types of drive backplane used in the server: one that controls only SAS drives and one that
controls both SAS and NVMe drives. Cable routing for drive components is different for SAS and SAS/NVMe
drives:

• SAS drive backplane connectors

.

Server components

39

«
...
47
48
49
50
51
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

UniServer R6900 G5

Brand: H3C Pages: 83

Brand: N-Tron Pages: 55

Brand: Vxl Pages: 2

callpilot 1002rp

Brand: Avaya Pages: 150

FileStore N8300

Brand: Symantec Pages: 55

Brand: TRENDnet Pages: 3

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 25

DIRECTORY SERVER 2.0 - GATEWAY

Brand: Red Hat Pages: 66

Brand: innuos Pages: 9

Brand: innuos Pages: 13

Brand: Avere Pages: 52

Brand: Intel Pages: 56

S5000VCL - Server Board Motherboard

Brand: Intel Pages: 74

Brand: Intel Pages: 82

TIGI2U - Carrier Grade Server

Brand: Intel Pages: 114

Brand: Oracle Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands