Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 29 | Manualshive

Page: 29 / 296

background image

Step 5. Update ESXi.

• The latest best recipe is available at:

https://datacentersupport.lenovo.com/us/en/solutions/ht505302

• The upgrade instructions are available at:

https://docs.vmware.com/en/VMware-vSphere/6.7/com.vmware.vsphere.virtualsan.doc/GUID-
B387B369-2800-4044-8B4C-C0537E61ECE4.html

• Instructions on upgrading ESXi using VUM are available at:

https://kb.vmware.com/s/article/1019545

Step 6. Update all the drivers to the latest best recipe levels by using VUM.

• The latest best recipe is available at:

https://datacentersupport.lenovo.com/us/en/solutions/ht505302

• The upgrade instructions are available at:

https://kb.vmware.com/articleview?docId=2137856

Step 7. Update the vSAN cluster.

The upgrade instructions are available at:

https://docs.vmware.com/en/VMware-vSphere/6.7/com.vmware.vsphere.virtualsan.doc/GUID-
ABABC0DF-2519-4C8F-A5B1-2AECF86247AB.html

Step 8. Update the HCL to reflect the latest certified vSAN component compliance.

• The code is available at:

http://partnerweb.vmware.com/service/vsan/all.json.gz

• The upgrade instructions are available at:

https://kb.vmware.com/s/article/2145116

Firmware updates

Several options are available to update the firmware for the server.

Lenovo XClarity Administrator and Lenovo XClarity Integrator are the recommended tools for updates. You
can use the tools listed here to update to the most current firmware in a given Best Recipe for your
appliance/node and the devices that are installed in the server.

Note:

Lenovo typically releases firmware in bundles called UpdateXpress System Packs (UXSPs). To ensure

that all the firmware updates are compatible, you should check the code included in the UXSP against the
desired ThinkAgile VX Best Recipe and update all firmware at the same time. If you are updating firmware for
both the Lenovo XClarity Controller and UEFI, update the firmware for Lenovo XClarity Controller first. All
firmware for the cluster must be contained within one Best Recipe.

Best practices related to updating firmware is available at the following location:

http://lenovopress.com/LP0656

Important terminology

•

In-band update

. The installation or update is performed using a tool or application within an operating

system that is executing on the server’s core CPU.

.

19

«
...
27
28
29
30
31
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Panasonic Pages: 31

SUPERSERVER 5018A-MHN4

Brand: Supermicro Pages: 116

Brand: ICP DAS USA Pages: 4

ProtectServer External 2

Brand: SafeNet Pages: 22

DLAP-201 Series

Brand: ADLINK Technology Pages: 39

Brand: Autonomic Pages: 17

PRIMERGY TX2550 M4

Brand: Fujitsu Pages: 563

ApplianceStor 90

Brand: Rasilient Pages: 42

Brand: National Instruments Pages: 4

Brand: Red Hat Pages: 120

Brand: Gigafast Pages: 74

Brand: Supermicro Pages: 76

Brand: Supermicro Pages: 79

Brand: AirLive Pages: 133

Brand: Planex Pages: 70

Brand: Planex Pages: 101

Brand: GIGA-BYTE TECHNOLOGY Pages: 141

Brand: x-odos Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands