Lenovo ThinkAgile MX Certified Node 2U User Manual Download Page 51 | Manualshive

Page: 51 / 104

background image

After installing all hot-swap drives, if you have removed the security bezel, reinstall it.

Hot-swap power supply replacement

Use this information to remove and install a hot-swap power supply.

Remove a hot-swap power supply

Use this information to remove a hot-swap power supply.

Guidelines” on

Static Sensitive Device

Ground package before opening”

S035

CAUTION:
Never remove the cover on a power supply or any part that has this label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with one
of these parts, contact a service technician.

S002

CAUTION:
The power control button on the device and the power switch on the power supply do not turn off the
electrical current that is supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.

S001

.

Hardware replacement procedures

47

«
...
49
50
51
52
53
...
»

Summary of Contents for ThinkAgile MX Certified Node 2U









































































































Reviews:

No comments

Related manuals for ThinkAgile MX Certified Node 2U

ALTOS R910 Series

Brand: Acer Pages: 74

Serial Servers Vlinx VESR9xx

Brand: B&B Electronics Pages: 61

Brand: G-Technology Pages: 35

6219 - IntelliStation M - Pro

Brand: IBM Pages: 317

Brand: 360 Systems Pages: 117

Brand: I-O DATA Pages: 49

Brand: Jatheon Pages: 52

Brand: Conceptronic Pages: 127

Brand: HIKVISION Pages: 13

AcquiLite EMB A7810

Brand: Obvius Pages: 29

301P - DP Print Server

Brand: D-Link Pages: 150

Brand: Avaya Pages: 270

Brand: BITMAIN Pages: 15

DIRECTORY SERVER 8.0

Brand: Red Hat Pages: 552

Brand: AirLive Pages: 133

Brand: Seeed Pages: 9

Brand: Abekas Pages: 382

72335LU - System x3850 M2

Brand: IBM Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands