Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 52

Page: 52 / 84

To install the ThinkSystem NE0152T RackSwitch in a standard equipment rack, complete the following
steps:

Step 1. Locate, record, and retain the product switch information in order to configure and register your

product.

Step 2. Attach a mounting bracket (item 1 in the illustration) to each side of the switch with M4 screws (item

2). Torque the screws to approximately 2.0 newton‐meters (Nm) ± 0.1 Nm (17.7 inch‐pounds).

Figure 25. Attaching mounting brackets to switch

Step 3. From the front, slide the switch into the rack at the desired height.

Step 4. Secure the switch unit to the rack posts with M6 screws (item 3 in illustration), washers (item 6), and

either clip nuts (item 4) or cage nuts (item 5). Torque the screws to approximately 5.7 Nm ± 0.1 Nm
(50 inch‐pounds).

Figure 26. Securing switch to rack posts

Lenovo ThinkAgile CP Hardware Installation Guide

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands