Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 41

Page: 41 / 84

Install the compute slide rails

Procedures for installing ThinkAgile CP compute block slide rails in a rack.

The slide rails are extensible as shown in the following illustration:

Figure 17. Slide rails

To install the ThinkAgile CP compute block slide rails, do the following:

Step 1. Ensure that the slide rail is shortened to its shortest position.

Step 2. From the front of the rack cabinet, line up the pins on the rear of the slide rail with the flange holes

at the rear of the rack.

Step 3. Push the slide rail so that the pins and the latch snap into place.

Note:

The holes on the rack are either be square-shaped or round-shaped.

Figure 18. Left slide rear installation

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands