Lenovo System x3750 M4 Installation And Service Manual Download Page 173 | Manualshive

Page: 173 / 982

background image

Step 6.

See controller and management software documentation.

If the problem is associated with a

specific function (for example, if a RAID hard disk drive is marked offline in the RAID array), see the
documentation for the associated controller and management or controlling software to verify that
the controller is correctly configured.

Problem determination information is available for many devices such as RAID and network
adapters.

For problems with operating systems, software, or devices, go to http://www.lenovo.com/support.

Step 7.

Check for troubleshooting procedures and RETAIN tips.

Troubleshooting procedures and

RETAIN tips document known problems and suggested solutions. To search for troubleshooting
procedures and RETAIN tips, go to http://www.lenovo.com/support.

Step 8.

Use the troubleshooting tables.

See “Troubleshooting by symptom” on page 180 to find a solution

to a problem that has identifiable symptoms.

A single problem might cause multiple symptoms. Follow the troubleshooting procedure for the
most obvious symptom. If that procedure does not diagnose the problem, use the procedure for
another symptom, if possible.

If the problem remains, contact an approved warranty service provider for assistance with
additional problem determination and possible hardware replacement. To open an online service
request, go to http://www.ibm.com/support/ entry/portal/Open_service_request. Be prepared to
provide information about any error codes and collected data.

Undocumented problems

If you have completed the diagnostic procedure and the problem remains, the problem might not have been
previously identified. After you have verified that all code is at the latest level, all hardware and software
configurations are valid, and no light path diagnostics LEDs or log entries indicate a hardware component
failure, contact an approved warranty service provider for assistance.

To open an online service request, go to http://www.ibm.com/support/ entry/portal/Open_service_request.
Be prepared to provide information about any error codes and collected data and the problem determination
procedures that you have used.

Service bulletins

This section describes how to locate service bulletins for this server.

The support website is continually updated with the latest tips and techniques that you can use to solve
problem that you might have with the Lenovo System x3750 M4 server. To find service bulletins that are
available for the server, go to http://www.ibm.com/supportportal/ and search for

8753

and

retain

.

Checkout procedure

The checkout procedure is the sequence of tasks that you should follow to diagnose a problem in the server.

About the checkout procedure

Before you perform the checkout procedure for diagnosing hardware problems, review the information in
this section.

• Read the safety information, see “Safety” on page v.

Troubleshooting

159

«
...
171
172
173
174
175
...
»

Summary of Contents for System x3750 M4























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3750 M4

Redbooks ServeRAID-MR10k

Brand: IBM Pages: 48

Brand: B&B Electronics Pages: 2

A+ AS-2124US-TNRP

Brand: Supermicro Pages: 130

NovaScale T840 E2

Brand: Bull Pages: 210

376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch

Brand: HP Pages: 169

Brand: Boundless Pages: 33

Brand: SpectraLink Pages: 31

Brand: 2Wire Pages: 2

Brand: BITMAIN Pages: 10

Brand: Excito Pages: 154

ANTMINER S19a Pro

Brand: BITMAIN Pages: 17

Brand: Advantech Pages: 6

Brand: B&B Electronics Pages: 39

Brand: Supero Pages: 90

A+ SERVER 2022G-URF

Brand: Supero Pages: 94

Brand: Supero Pages: 94

A+ SERVER 2042G-6RF

Brand: Supero Pages: 114

Brand: Supero Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands