manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 238

0

0

0

0

0

0

0

0000

0000

00

00

000000

000000

000000

0000

0000

0000000

0000000

0000000

0000000

Rear two hard-disk-drive kit

Figure 148. Rear two hard-disk-drive kit installation

Step 6.

Press down on the kit. Make sure that the kit is fully seated in the connector on the system board.

Step 7.

Replace the cover (see “Replacing the cover” on page 196).

Step 8.

Slide the server into the rack.

Step 9.

Reconnect the power cords and any cables that you removed.

Step 10. Turn on the peripheral devices and the server.

Removing an adapter

Use this information to remove an adapter.

Removing an adapter from a PCI riser-card assembly

Use this information to remove an adapter from a PCI expansion slot in a PCI riser-card assembly. These
instructions apply to PCI adapters such as video graphic adapters and network adapters.

The following table shows the locations of the adapter expansion slots from the rear of the server.

Table 22. The maximum adapter dimension supported in each slot (rear view)

PCI riser-card assembly 1

PCI riser-card assembly 2

1

Full height, up to full length

4

Full height, up to full length

2

Full height, half length

5

Full height, up to full length

3

Full height, half length

6

Full height, half length

226

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands