manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 210

Hex screw driver

Figure 119. Bezel removal

Step 4.

Rotate the top of the bezel away from the server.

Step 5.

Remove the operator information panel assembly (see “Removing the operator information panel
assembly” on page 278).

If you are instructed to return the bezel, follow all packaging instructions, and use any packaging materials
for shipping that are supplied to you.

Replacing the bezel

Use this information to replace the bezel.

To install the bezel, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Reinstall the operator information panel assembly in the bezel, if it has been removed earlier (see
“Replacing the operator information panel assembly” on page 279).

Step 4.

Insert the tabs on the bottom of the bezel into the slots on the underside of the chassis and attach
it with the screws.

Note:

Use the hex screw driver to install the screws.

198

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands