manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 192

00000000

00000000

00000000

0000000

0000000

0000000

Video and USB breakout
signal cable

Figure 101. Front USB and video cable connection

Cabling operator information panel

The internal routing and connectors for the operator information panel.

The following notes describe additional information you must consider when you install or remove the
operator information panel cable:

• You may remove the optional optical drive cable to obtain more room before you install or remove the

operator information panel cable.

• To remove the operator information panel cable, slightly press the cable toward the fan cage; then, pull to

remove the cable from the connector on the system board. Pulling the cable out of the connector by
excessive force might cause damage to the cable or connector.

• To connect the operator information panel cable on the system board, press evenly on the cable. Pressing

on one side of the cable might cause damage to the cable or connector.

Attention:

Failing to install or remove the cable with care may damage the connectors on the system board.

Any damage to the connectors may require replacing the system board.

180

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands