manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 174

• Diagnostic program type and version level

• Configuration option settings

• Operating-system control-file setup

See Appendix D “Getting help and technical assistance” on page 1135 for information about calling Lenovo
for service.

Recovering the server firmware (UEFI update failure)

Use this information to recover the server firmware.

Important:

Some cluster solutions require specific code levels or coordinated code updates. If the device

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before
you update the code.

If the server firmware has become corrupted, such as from a power failure during an update, you can
recover the server firmware in the following way:

•

In-band method:

Recover server firmware, using either the boot block jumper (Automated Boot

Recovery) and a server Firmware Update Package Service Pack.

•

Out-of-band method:

Use the IMM web interface to update the firmware, using the latest server

firmware update package.

Notes:

You can obtain a server update package from one of the following sources:

• Download the server firmware update from the World Wide Web.

• Contact your Lenovo service representative.

To download the server firmware update package from the World Wide Web, go to
http://www.lenovo.com/support.

The flash memory of the server consists of a primary bank and a backup bank. You must maintain a bootable
UEFI firmware image in the backup bank. If the server firmware in the primary bank becomes corrupted, you
can either manually boot the backup bank with the UEFI boot backup jumper (JP7), or in the case of image
corruption, this will occur automatically with the Automated Boot Recovery function.

In-band manual recovery method

Use this information to recover the server firmware and restore the server operation to the primary bank.

To recover the server firmware and restore the server operation to the primary bank, complete the following
steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server, and disconnect all power cords and external cables.

Step 3.

Remove the cover (see “Removing the cover” on page 37).

Step 4.

Locate the UEFI boot backup jumper (JP7) on the system board.

162

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands