manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 5.

Loosen the screws. Then, remove the COM port bracket connector from the opening of PCIe
riser 2 assembly.

COM port

Figure 183. COM port bracket connector insertion into PCIe riser 2 assembly

Note:

For some it may be easier to remove the COM port bracket by first slightly removing PCIe

riser 2 assembly from the system board.

Step 6.

If you are instructed to return the COM port bracket, follow all packaging instructions, and use
any packaging materials for shipping that are supplied to you.

Replacing the COM port bracket

Use this information to replace the COM port bracket.

To install the COM port bracket, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Step 3.

If necessary, remove PCIe riser 2 assembly from the system board (see “Removing a PCI riser-card
assembly” on page 169).

258

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Kaleidescape Terra Installation Manual preview
Terra
Brand: Kaleidescape Pages: 11
NEC Express5800/T110g-E Quick Start Manual preview
Express5800/T110g-E
Brand: NEC Pages: 2
IBM xSeries 235 Maintenance & Troubleshooting preview
xSeries 235
Brand: IBM Pages: 214
CAAS Audio Digital Audio Server User Manual & Warranty preview
Digital Audio Server
Brand: CAAS Audio Pages: 23
Quanta Computer STRATOS S400-X44E Technical Manual preview
STRATOS S400-X44E
Brand: Quanta Computer Pages: 251
IBM 88632SU User Manual preview
88632SU
Brand: IBM Pages: 100
ADLINK Technology DLAP-201 Series User Manual preview
DLAP-201 Series
Brand: ADLINK Technology Pages: 39
IBM eserver iSeries 270 Installation Manual preview
eserver iSeries 270
Brand: IBM Pages: 40
Airlink101 AMPS240W User Manual preview
AMPS240W
Brand: Airlink101 Pages: 36
Buffalo TERASTATION HS-D1.0TGL/R5 Technical Specifications preview
TERASTATION HS-D1.0TGL/R5
Brand: Buffalo Pages: 2
ZLAN ZLAN5443A User Manual preview
ZLAN5443A
Brand: ZLAN Pages: 13
Speco ONSIP OS101 User Manual preview
ONSIP OS101
Brand: Speco Pages: 28
3onedata NP301 Quick Installation Manual preview
NP301
Brand: 3onedata Pages: 3
IBM System x3610 User Manual preview
System x3610
Brand: IBM Pages: 90
Fusion FusionServer 2298 V5 Manual preview
FusionServer 2298 V5
Brand: Fusion Pages: 89
Hitachi F1500 Hardware Manual preview
F1500
Brand: Hitachi Pages: 208
Hitachi AMS 2500 Getting Started Manual preview
AMS 2500
Brand: Hitachi Pages: 36
D-Link DPR-1260 - RangeBooster G Multifunction Print Server User Manual preview
DPR-1260 - RangeBooster G Multifunction Print Server
Brand: D-Link Pages: 55

Brands by name

Popular brands

Load more brands