manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Four 3.5-inch hot-swap or simple-swap hard disk drive server configuration:

Media cage

Video connector

Screws

Figure 167. Front video connector assembly removal for four 3.5-inch hot-swap or simple-swap hard disk
drive server configuration

Step 6.

If you are instructed to return the front video connector assembly, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing the front video connector assembly

Use this information to replace the front video connector assembly.

To install the front video connector assembly, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

From inside the media cage, insert the front video connector assembly into the holes on the cage;
then, install the screws to secure the assembly to the cage.

Note:

Refer to the illustration that applies to your particular server configuration.

246

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

D-Link ShareCenter DNS-343 Quick Install Manual preview
ShareCenter DNS-343
Brand: D-Link Pages: 12
D-Link DP 301U Quick Installaion Manual preview
DP 301U
Brand: D-Link Pages: 12
NEC NECCare Gold Express5800/320Fd Service Manual preview
NECCare Gold Express5800/320Fd
Brand: NEC Pages: 10
NEC SV8500 Setup Manual preview
SV8500
Brand: NEC Pages: 84
NEC NEC Express5800 Series Release Note preview
NEC Express5800 Series
Brand: NEC Pages: 6
Panasonic KX-NS1000 Configuration Manual preview
KX-NS1000
Brand: Panasonic Pages: 31
AXIOMTEK NA-1301 Hardware Installation Manual preview
NA-1301
Brand: AXIOMTEK Pages: 55
GlobalTime Electronic GTT-400 Manual preview
GTT-400
Brand: GlobalTime Electronic Pages: 19
Supero SUPERSERVER 1018D-73MTF User Manual preview
SUPERSERVER 1018D-73MTF
Brand: Supero Pages: 124
Ekselans 280053 User Manual preview
280053
Brand: Ekselans Pages: 37
IBM @server x Series Quick Setup Manual preview
@server x Series
Brand: IBM Pages: 8
Viavi G4-GigaFlow Manual preview
G4-GigaFlow
Brand: Viavi Pages: 11
Black Box RAS-PutIn Installation And User Manual preview
RAS-PutIn
Brand: Black Box Pages: 93
SSS Siedle AS 670-0 S Product Information preview
AS 670-0 S
Brand: SSS Siedle Pages: 12
C-MOR GP User Manual preview
GP
Brand: C-MOR Pages: 43
Symmetricom SyncServer S100 User Manual preview
SyncServer S100
Brand: Symmetricom Pages: 166
VBrick Systems EtherneTV User Manual preview
EtherneTV
Brand: VBrick Systems Pages: 44
FreeNAS 1U Basic Setup & Deployment preview
1U
Brand: FreeNAS Pages: 4

Brands by name

Popular brands

Load more brands