manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Four 3.5-inch-drive server model:

Figure 158. Media cage installation for four 3.5-inch-drive server model

Step 3.

Reinstall the air baffle (see “Replacing the air baffle” on page 122).

Step 4.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 5.

Slide the server into the rack.

Step 6.

Reconnect the power cords and any cables that you removed.

Step 7.

Turn on the peripheral devices and the server.

Removing the front USB connector assembly

Use this information to remove the front USB connector assembly.

To remove the front USB connector assembly, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords; then, remove the
cover (see “Removing the cover” on page 119).

Step 3.

Remove the media cage (see “Removing the media cage” on page 234).

Step 4.

Remove the front USB connector assembly from the media cage.

Notes:

• Refer to the illustration that applies to your particular server configuration.

240

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

TYANO GX38-B5550 Service Engineer'S Manual preview
GX38-B5550
Brand: TYANO Pages: 68
Sun Oracle SPARC T3-2 Service Manual preview
SPARC T3-2
Brand: Sun Oracle Pages: 222
CNET CNP-101UW Specifications preview
CNP-101UW
Brand: CNET Pages: 2
xFusion Digital Technologies FusionServer G8600 V7 Manual preview
FusionServer G8600 V7
Brand: xFusion Digital Technologies Pages: 112
Bull NovaScale T840 E2 User Manual preview
NovaScale T840 E2
Brand: Bull Pages: 210
IBM System x3610 User Manual preview
System x3610
Brand: IBM Pages: 90
IBM eServer xSeries 335 Type 8676 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 335 Type 8676
Brand: IBM Pages: 178
Dell Force10 MXL Blade Specifications preview
Force10 MXL Blade
Brand: Dell Pages: 2
Canon imagePRESS Server G200 Configuration And Setup preview
imagePRESS Server G200
Brand: Canon Pages: 98
Canon imagePRESS A3200 Installation And Service Manual preview
imagePRESS A3200
Brand: Canon Pages: 192
Canon ColorPass-Z7400 Configuration Manual preview
ColorPass-Z7400
Brand: Canon Pages: 210
Usl CMS-2200 Quick Start Manual preview
CMS-2200
Brand: Usl Pages: 4
High End Systems CATALYST DV User Manual preview
CATALYST DV
Brand: High End Systems Pages: 224
Excito BUBBA User Manual preview
BUBBA
Brand: Excito Pages: 46
Tibbo TCP001 Manual preview
TCP001
Brand: Tibbo Pages: 12
Silicon Graphics International SGI UV 30 User Manual preview
SGI UV 30
Brand: Silicon Graphics International Pages: 68
Silicon Graphics UV 2000 System User'S Manual preview
UV 2000
Brand: Silicon Graphics Pages: 116
Vlinx ESP901 Manual preview
ESP901
Brand: Vlinx Pages: 47

Brands by name

Popular brands

Load more brands