manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 3.

Grasp the orange fan tabs on both ends of the fan and slowly lift it out of the chassis.

Fan 8

Fan connector on
the system board

Fan tabs

Figure 118. Fan removal

If you are instructed to return the fan, follow all of the packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Replacing a thermal kit (hot-swap fan)

Use this information to replace a thermal kit (hot-swap fan).

The server comes standard with five dual-motor hot-swap cooling fans. When there is one microprocessor
installed, install fan 1, 2, 3, 5, and 7 for proper cooling.

Attention:

To ensure proper operation, replace a failed hot-swap fan within 30 seconds.

To replace a hot-swap fan, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Remove the cover (see “Removing the cover” on page 119).

Step 3.

Touch the static-protective package that contains the new fan to any unpainted metal surface on
the server. Then, remove the new fan from the package.

194

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Newtec NOP1840 PEP-Box User Manual preview
NOP1840 PEP-Box
Brand: Newtec Pages: 96
Jung SV-SERVER-01 Operating Instructions Manual preview
SV-SERVER-01
Brand: Jung Pages: 16
7thSense M101-4 User Manual preview
M101-4
Brand: 7thSense Pages: 28
AIC FB128-LX User Manual preview
FB128-LX
Brand: AIC Pages: 79
I-O DATA FIDATA HFAS1-S10U Setup Manual preview
FIDATA HFAS1-S10U
Brand: I-O DATA Pages: 46
Infrant Technologies ReadyNAS Duo User Manual preview
ReadyNAS Duo
Brand: Infrant Technologies Pages: 98
Huawei XH628 V5 Quick Start Manual preview
XH628 V5
Brand: Huawei Pages: 2
Huawei X6800 Technical Manual preview
X6800
Brand: Huawei Pages: 52
Huawei V100R002C01 User Manual preview
V100R002C01
Brand: Huawei Pages: 122
Huawei U-SYS MRS6100 Technical Manual preview
U-SYS MRS6100
Brand: Huawei Pages: 131
Huawei UPS5000-E-****-FM series User Manual preview
UPS5000-E-****-FM series
Brand: Huawei Pages: 261
Wieland 83.040.0500.0 Manual preview
83.040.0500.0
Brand: Wieland Pages: 42
Viavi G4-Apex-ENTERPRISE-HW Hardware Installation preview
G4-Apex-ENTERPRISE-HW
Brand: Viavi Pages: 8
Supermicro SUPERSERVER 6026TT-IBQF User Manual preview
SUPERSERVER 6026TT-IBQF
Brand: Supermicro Pages: 100
Supermicro SuperServer 510P-WT User Manual preview
SuperServer 510P-WT
Brand: Supermicro Pages: 113
Supermicro SuperWorkstation 7049GP-TRT User Manual preview
SuperWorkstation 7049GP-TRT
Brand: Supermicro Pages: 133
Inspur NF5166M4 User Manual preview
NF5166M4
Brand: Inspur Pages: 147
Tektronix MSO54 Programmer'S Manual preview
MSO54
Brand: Tektronix Pages: 1026

Brands by name

Popular brands

Load more brands