manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 4.

Remove the screws from the EIA bracket.

Note:

Use the T8 torx wedge to remove the screws.

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

T8 torx wrench

Figure 51. Screw removal

Step 5.

Slightly side the EIA bracket to the right; then, remove it from the chassis.

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

EIA bracket

Figure 52. EIA bracket removal

Replacing the EIA bracket

Use this information to replace the EIA bracket.

To replace the EIA bracket, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

134

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

NEC HX4500 Configuration Manual preview
HX4500
Brand: NEC Pages: 74
NEC Express5800/T120e Quick Start Manual preview
Express5800/T120e
Brand: NEC Pages: 6
NEC Express5800/T120e Getting Started preview
Express5800/T120e
Brand: NEC Pages: 2
NEC Express5800/T110i Getting Started preview
Express5800/T110i
Brand: NEC Pages: 2
NEC EXPRESS5800/R320d-E4 Configuration Manual preview
EXPRESS5800/R320d-E4
Brand: NEC Pages: 19
NEC Express5800/R320d-M4 Series User Manual preview
Express5800/R320d-M4 Series
Brand: NEC Pages: 98
NEC Express5800/R120h-2M Getting Started preview
Express5800/R120h-2M
Brand: NEC Pages: 2
NEC Express5800/R120f-1E Use Precautions preview
Express5800/R120f-1E
Brand: NEC Pages: 12
NEC Express5800/R120d-1E Hardware Specification preview
Express5800/R120d-1E
Brand: NEC Pages: 2
NEC Express5800/R110i-1 Getting Started preview
Express5800/R110i-1
Brand: NEC Pages: 2
NEC Express5800/R110h-1 System Configuration Manual preview
Express5800/R110h-1
Brand: NEC Pages: 40
NEC Express5800/A2040d Configuration Manual preview
Express5800/A2040d
Brand: NEC Pages: 83
NEC Express5800/320Lc Datasheet preview
Express5800/320Lc
Brand: NEC Pages: 4
NEC Express5800/120Rj-2 Datasheet preview
Express5800/120Rj-2
Brand: NEC Pages: 2
NEC NEAX2000 IVS2 Manual preview
NEAX2000 IVS2
Brand: NEC Pages: 106
NEC Express5800/T120d User Manual preview
Express5800/T120d
Brand: NEC Pages: 153
NEC Express5800/T110g-S User Manual preview
Express5800/T110g-S
Brand: NEC Pages: 128
NEC Express5800/R120g-1E Maintenance Manual preview
Express5800/R120g-1E
Brand: NEC Pages: 224

Brands by name

Popular brands

Load more brands