manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

Share
Download
Lenovo System x3250 M5 Installation And Service Manual Download Page 290

Figure 202. 3.5-inch simple-swap hard disk drive with ServeRAID SAS/SATA controller cable connection (hardware
RAID card inserted on the left side)

Cabling the hard disk drive with ServeRAID SAS/SATA controller for redundant
power supply model

This section shows the cable routing for the hot-swap and simple-swap hard disk drive with ServeRAID
SAS/SATA controller for the redundant power supply model.

Cabling the hot-swap hard disk drive with ServeRAID SAS/SATA controller (redundant power supply
model)

The internal routing and connectors for the hot-swap hard disk drive with ServeRAID SAS/SATA controller
(redundant power supply model).

The following illustrations show the internal routing and connectors for the 2.5-inch hot-swap hard disk
drive models with ServeRAID SAS/SATA controller.

Note:

Make sure the relevant cables pass through the cable clips.

276

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands