manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

Share
Download
Lenovo System x3250 M5 Installation And Service Manual Download Page 239

Figure 152. 2.5-inch hot-swap hard disk drive backplane removal

Step 4.

Disconnect all cables from the hard disk drive backplane.

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing the 2.5-inch hot-swap hard disk drive backplane

Use this information to replace the 2.5-inch hot-swap hard disk drive backplane.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31.

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

To replace the 2.5-inch hot-swap hard disk drive backplane, complete the following steps:

Step 1.

Reconnect all cables that you removed from the hard disk drive backplane.

Step 2.

Align the backplane with the backplane alignment slots in the chassis.

Step 3.

Lower the backplane into the slot in the chassis until the front tab clicks into the latches on the
chassis.

Chapter 6

.

Removing and replacing server components

225

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands