manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

Share
Download
Lenovo System x3250 M5 Installation And Service Manual Download Page 197

Figure 111. DVD drive cable latch

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing the DVD drive cable

Use this information to replace the DVD drive cable.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31.

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

To replace the DVD drive cable, complete the following steps:

Step 1.

Align the cable connector with the connector on the rear of the DVD drive cage. Press the cable
connector into the DVD drive cage connector and slide the cable connector to the left (locked
position) to lock the cable in place.

Figure 112. DVD drive cable latch

Chapter 6

.

Removing and replacing server components

183

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands