Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 37

Page: 37 / 1022

Power distribution
board connector

DIMM 16

DIMM 15

DIMM 14

DIMM 13

DIMM 12

DIMM 11

DIMM 10

DIMM 9

PCI riser
connector 2

SAS connector

PCI riser
connector 1

USB hypervisor
key

DIMM 5

DIMM 6

DIMM 7

DIMM 8

DIMM 4

DIMM 3

DIMM 2

DIMM 1

Microprocessor 2

Microprocessor 1

HDD Backplane connector

IMM/SAS connector

Slot 6

SD adapter
connector

Slot 7

Rear HDD power
connector

HDD LED signal
connector

Figure 10. Internal connectors on system board

System-board external connectors

The following illustration shows the external connectors on the system board.

Chapter 1

The Lenovo NeXtScale nx360 M5 compute node

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NeXtScale nx360 M5

Reviews:

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 37 / 1022

Search results

Summary of Contents for NeXtScale nx360 M5

Reviews: