manualshive.com logo in svg

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 171 / 1022

Share
Download
Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 171

Figure 83. DIMM connectors location

DIMM installation sequence

Depending on the server model, the server may come with a minimum of one 4 GB DIMM installed in slot
4. When you install additional DIMMs, install them in the order shown in the following table to optimize
system performance.

In general, all channels on the memory interface for each microprocessor can be populated in any order
and have no matching requirements.

Table 11. Normal mode DIMM installation sequence

Number of installed
microprocessor

DIMM connector population sequence

One microprocessor installed

8, 1, 6, 3, 7, 2, 5, 4

Two microprocessors installed

8, 9, 1, 16, 6, 11, 3, 14, 7, 10, 2, 15, 5, 12, 4, 13

Chapter 5

.

Removing and replacing components

157

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments