Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 154

Page: 154 / 1022

Replacing a RAID adapter battery holder

Use this information to install a RAID adapter battery holder.

Before you install a RAID adapter battery holder, complete the following steps:

1. Read “Safety” on page v and “Installation guidelines” on page 101.

2. If the compute node is installed in a NeXtScale n1200 Enclosure, remove it (see “Removing a compute

node from a chassis” on page 104 for instructions).

3. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with

the bezel pointing toward you.

To install a RAID adapter battery holder, complete the following steps:

Step 1.

Remove the cover (see “Removing the compute node cover” on page 113).

Step 2.

Align the battery holder hooks and place the battery holder on the air baffle.

Battery holder

Hook

Air baffle

Latch

Figure 62. RAID adapter battery holder alignment

Step 3.

Press the latch and push the battery holder forward to the hook.

140

Lenovo NeXtScale nx360 M5 Installation and Service Guide

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NeXtScale nx360 M5

Reviews:

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 154 / 1022

Search results

Summary of Contents for NeXtScale nx360 M5

Reviews: