manualshive.com logo in svg

Lenovo Moto One Hyper, Service And Repair Manual, Page: 98 / 138

Share
Download
Lenovo Moto One Hyper Service And Repair Manual Download Page 98

Lenovo Moto One Hyper 
Level 2 

– Service and Repair Manual 

 

 

Lenovo Confidential Restricted: 

PAGE 98 

 

Do not share without consent from Lenovo 

Battery Assembly 

Description 

Reference # 

Defender TPLCM Assy Etching ICE LATAM 

Defender TPLCM Assy Etching SAN LATAM 

Defender TPLCM Assy Etching TER LATAM 

Defender TPLCM Assy Etching ICE EU 

Defender TPLCM Assy Etching SAN EU 
Defender TPLCM Assy Etching ICE APEM 

Defender TPLCM Assy Etching TER APEM 

Defender TPLCM Assy Etching ICE CN 

Defender TPLCM Assy Etching TER CN 

Defender TPLCM Assy Etching ICE RU 
Defender TPLCM Assy Etching ICE BR 

Defender TPLCM Assy Etching SAN BR 

Defender TPLCM Assy Etching TER BR 

Defender FRU TPLCM Front HSG Assy ICE 

Defender FRU TPLCM Front HSG Assy SAN 

Defender FRU TPLCM Front HSG Assy TER 

1 

ACCY,BAT,BATTERY;4000mAh;KG50;ATL486770; 

7 

 

/// WARNING /// 

Failure to adhere to Safety Critical Note(s) may 

increase risk of rupture, burning, or failure to 
function safely when used by the customer. 
Refer to the Battery Safety Guidelines. 

 

// CAUTION // 

Handle the Battery Pack with care. If dropped to the 

floor, it may be internally damaged and must be 
scrapped. 

Ensure Battery and its insulation are not damaged (e.g. 

scratched, dented, punctured) prior to and throughout 
assembly. 

Prior to assembly, ensure Battery edges and surfaces 
are not dented or deformed, and that fixtures and parts 
that will contact the Battery are free of foreign material. 

Ensure screws and screwdrivers do not contact the 
Battery. 

 

1.

 

Place the Battery Adhesive on the location as 
shown and peel off the liner. 

 

Summary of Contents for Moto One Hyper











































































































































Reviews:

No comments