manualshive.com logo in svg

Lenovo Moto One Hyper, Service And Repair Manual, Page: 111 / 138

Share
Download
Lenovo Moto One Hyper Service And Repair Manual Download Page 111

Lenovo Moto One Hyper 
Level 2 

– Service and Repair Manual 

 

 

Lenovo Confidential Restricted: 

PAGE 111 

 

Do not share without consent from Lenovo 

Sub Board Assembly 

Description 

Reference # 

Defender TPLCM Assy Etching ICE LATAM 

Defender TPLCM Assy Etching SAN LATAM 

Defender TPLCM Assy Etching TER LATAM 

Defender TPLCM Assy Etching ICE EU 

Defender TPLCM Assy Etching SAN EU 
Defender TPLCM Assy Etching ICE APEM 

Defender TPLCM Assy Etching TER APEM 

Defender TPLCM Assy Etching ICE CN 

Defender TPLCM Assy Etching TER CN 

Defender TPLCM Assy Etching ICE RU 
Defender TPLCM Assy Etching ICE BR 

Defender TPLCM Assy Etching SAN BR 

Defender TPLCM Assy Etching TER BR 

Defender FRU TPLCM Front HSG Assy ICE 

Defender FRU TPLCM Front HSG Assy SAN 

Defender FRU TPLCM Front HSG Assy TER 

1 

Sub PCBA,Defender 

Defender FRU Sub BRD CS 

4 

HDW,SCR,SCR, M1.0 x 0.20 x 1.4 Cross, BL 

HDW,SCR,Screws M1.2x0.25 x 1.7, SLVR 

SCR,SCREWS M1.4X0,3X3 

23 

 

1.

 

Use fingers to place the Sub Board on the 
location as shown. 

 

2.

 

Use the Torque Driver with Philips PH00 Bit 
to tighten the white screw as shown (0.7±0.1 
kgf-cm). 

 

 

 

Summary of Contents for Moto One Hyper











































































































































Reviews:

No comments