background image

iii 

 

 

Safety information

General Safety guidelines

For tips to help you use your computer safely

go to:

http://www.lenovo.com/safety

Before installing this product, read the Safety Information.

DANGER

To avoid shock hazard:

• Do not remove the covers.
• Do not operate this product unless the stand is attached.
• Do not connect or disconnect this product during an electrical storm.
• The power cord plug must be connected to a properly wired and grounded 

power outlet.

• Any equipment to which this product will be attached must also be connected to 

properly wired and grounded power outlets.

• To isolate the monitor from the electrical supply, you must remove the plug from 

the power outlet. The power outlet should be easily accessible.

To take special precautions to avoid the introduction of hazards when operating

installing

 

servicing

transporting or storing equipment

the necessary instructions shall be made 

available.
To reduce the risk of electric shock

do not perform any servicing other than that contained in 

the operating instructions unless you are qualified to do so.

Handling:

• If your monitor weighs more than 18 kg (39.68 lb), it is recommended that it be 

moved or lifted by two people.

Make sure the light bar is located downside when using VESA mount setup. 

Summary of Contents for LI2721s

































Reviews: