Lenovo IdeaPad S200 Hardware Maintenance Manual Download Page 106

Page: 106 / 138

• To complete the installation or replacement, go to “Completing the parts replacement” on page 109.

Replacing the PCI Express card

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the PCI Express card, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 82.

3. Locate the PCI Express card. See “Computer components” on page 31 .

4. At the rear of the computer, remove the screw

to open the card latch.

Figure 37. Opening the PCI Express card latch

100

Lenovo S200 Hardware Maintenance Manual

Summary of Contents for IdeaPad S200











































































































































Search results

Summary of Contents for IdeaPad S200

Reviews:

Related manuals for IdeaPad S200

Brands by name

Popular brands

Lenovo IdeaPad S200, Hardware Maintenance Manual

Search results

Summary of Contents for IdeaPad S200

Reviews:

Related manuals for IdeaPad S200

Brands by name

Popular brands