manualshive.com logo in svg

Lenovo ideacentre 510S, Hardware Maintenance Manual, Page: 67 / 92

Share
Download
Lenovo ideacentre 510S Hardware Maintenance Manual Download Page 67

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 48.

3. Remove the front bezel. See “Replacing the front bezel” on page 48.

4. Remove the optical drive. See “Replacing the optical drive” on page 49.

5. Remove the storage drive. See “Replacing the storage drive” on page 51.

6. Locate the coin-cell battery. See “Computer components” on page 30.

7. Remove the coin-cell battery as shown.

Figure 22. Removing the coin-cell battery

8. Install the new coin-cell battery as shown.

Figure 23. Installing the coin-cell battery

9. Reinstall the storage drive. See “Replacing the storage drive” on page 51.

10. Reinstall the optical drive. See “Replacing the optical drive” on page 49.

11. Reinstall the front bezel. See “Replacing the front bezel” on page 48.

12. Reinstall the computer cover and connect the cables. See “Completing the parts replacement” on

page 74.

13. Turn on the computer and all connected devices.

Note:

When the computer is turned on for the first time after replacing the coin-cell battery, an error

message might be displayed. This is normal after replacing the coin-cell battery.

14. Use the Setup Utility program to set the date, time, and any passwords. See “Completing the parts

replacement” on page 74.

Replacing the heat sink and fan assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1 .

CAUTION:

Chapter 6

.

Installing or replacing hardware

61

Summary of Contents for ideacentre 510S





























































































Reviews:

No comments