Lenovo HX3510-G Installation And Service Manual Download Page 52 | Manualshive

Page: 52 / 1240

background image

Use the backup copy of the server firmware until the primary copy is restored. After the primary copy is
restored, turn off the server; then, move the UEFI boot backup jumper (J15) back to the primary position
(pins 1 and 2).

The Update

Xpress

System Pack Installer

The Update

Xpress

System Pack Installer detects supported and installed device drivers and firmware in the

server and installs available updates.

For additional information and to download the Update

Xpress

System Pack Installer, go to the ToolsCenter

for System x and BladeCenter at http://publib.boulder.ibm.com/infocenter/toolsctr/v1r0/ and click

UpdateXpress System Pack Installer

.

Using the integrated management module

The integrated management module (IMM) is a second generation of the functions that were formerly
provided by the baseboard management controller hardware. It combines service processor functions, video
controller, and remote presence function in a single chip.

The IMM supports the following basic systems-management features:

• Alerts (in-band and out-of-band alerting, PET traps - IPMI style, SNMP, e-mail).

• Auto Boot Failure Recovery (ABR).

• Automatic microprocessor disable on failure and restart in a two-microprocessor configuration when one

microprocessor signals an internal error. When one of the microprocessors fail, the server will disable the
failing microprocessor and restart with the other microprocessor.

• Automatic Server Restart (ASR) when POST is not complete or the operating system hangs and the

operating system watchdog timer times-out. The IMM might be configured to watch for the operating
system watchdog timer and reboot the system after a timeout, if the ASR feature is enabled. Otherwise,
the IMM allows the administrator to generate a nonmaskable interrupt (NMI) by pressing an NMI button
on the LCD system information display panel (if available) for an operating-system memory dump. ASR
is supported by IPMI.

• A virtual media key, which enables remote presence support (remote video, remote keyboard/mouse,

and remote storage).

• Boot sequence manipulation.

• Command-line interface.

• Configuration save and restore.

• DIMM error assistance. The Unified Extensible Firmware Interface (UEFI) disables a failing DIMM that is

detected during POST, and the IMM lights the associated system error LED and the failing DIMM error LED.

• Environmental monitor with fan speed control for temperature, voltages, fan failure, power supply failure,

and power backplane failure.

• Intelligent Platform Management Interface (IPMI) Specification V2.0 and Intelligent Platform Management

Bus (IPMB) support.

• Invalid system configuration (CONFIG) LED support.

• LCD system information display panel (if available) reports errors that occur with fans, power supplies,

microprocessor, hard disk drives, and system errors.

• Local firmware code flash update

• Nonmaskable interrupt (NMI) detection and reporting.

• Operating-system failure blue screen capture.

• PCI configuration data.

40

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
50
51
52
53
54
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX3510-G

UniServer E3200 G3

Brand: H3C Pages: 401

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

Brand: BlueBroadcaster Pages: 21

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

Netfinity Series

Brand: IBM Pages: 44

Brand: IBM Pages: 82

SuperServer E300-9C

Brand: Supermicro Pages: 113

Brand: Syncronorm Pages: 17

Brand: Digi Pages: 124

Connectware PortServer TS 8/16

Brand: Digi Pages: 106

Brand: BITMAIN Pages: 20

Brand: Lantronix Pages: 135

Brand: Polycom Pages: 2

Brand: Black Box Pages: 2

Brand: Black Box Pages: 2

Brand: Black Box Pages: 8

Xtreme PC NG6452

Brand: Chip PC Pages: 4

Brand: Silicon Graphics Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands