Lenovo HX3510-G Installation And Service Manual Download Page 127

Page: 127 / 1240

SAS signal cable

Power / configuration cable

SAS 0 SAS 1 SAS 0 SAS 1 SAS 0 SAS 1

Figure 41. 24x2.5-inch hot-swap hard disk drive cabling

3.5-inch hard disk drive cable connection

The following illustrations show the cabling information for the 3.5-inch drive models.

Important:

Make sure all SAS cables are routed lower than the DIMM latches.

8x3.5-inch drive model (HX5510 and HX5510-C)

The internal routing for the 8x3.5-inch drive model cables.

The following illustration shows the internal routing for the 8x3.5-inch drive model cables.

Note:

There might be 3 or 4 power connectors on the system board depending on your configuration.

However, this difference will not affect the cable routing. Follow the following illustrations to complete
your cable routing.

Chapter 5

Removing, and replacing components

115

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands