Lenovo HX3510-G Installation And Service Manual Download Page 101 | Manualshive

Page: 101 / 1240

background image

Configuration changes, such as added devices or adapter firmware updates, and firmware or application
code problems can cause the server to fail POST (the power-on self-test). If this occurs, the server responds
in either of the following ways:

• The server restarts automatically and attempts POST again.

• The server hangs, and you must manually restart the server for the server to attempt POST again.

After a specified number of consecutive attempts (automatic or manual), the Nx-boot failure feature causes
the server to revert to the default UEFI configuration and start the Setup Utility so that you can make the
necessary corrections to the configuration and restart the server. If the server is unable to successfully
complete POST with the default configuration, there might be a problem with the system board.

To specify the number of consecutive restart attempts that will trigger the Nx-boot failure feature, in the
Setup Utility, click

System Settings

➙

Recovery

➙

POST Attempts

➙

POST Attempts Limit

. The

available options are 3, 6, 9, and 255 (disable Nx-boot failure).

Troubleshooting

89

«
...
99
100
101
102
103
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX3510-G

Brand: US Robotics Pages: 156

Virtual Services Platform 7000 Series

Brand: Avaya Pages: 103

SUPERSERVER 8045C-3R

Brand: Supermicro Pages: 118

NovaScale R410B F2

Brand: Bull Pages: 38

Brand: IBM Pages: 24

MediaGrid ContentServer 3000

Brand: Omneon Pages: 2

Brand: LiveU Pages: 14

Brand: TYAN Pages: 70

Brand: Waves Pages: 6

Brand: Fujitsu Pages: 26

Brand: Fujitsu Pages: 56

Brand: Fujitsu Pages: 36

Brand: Fujitsu Pages: 61

Brand: Fujitsu Pages: 30

ETERNUS DX Disk

Brand: Fujitsu Pages: 85

Brand: Fujitsu Pages: 111

BX630 - PRIMERGY - S2 Dual

Brand: Fujitsu Pages: 64

Brand: Fujitsu Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands